Vermont American® Abrasive Cut-Off Wheels
Class I - DangerousWhat Should You Do?
- Check if you have this product: (About 400,000)
- Do not eat it: Even if it looks and smells fine, do not consume this product.
- Throw it away or return it: You can return the product to the store for a full refund.
- Seek medical attention if needed: If you've consumed this product and feel unwell, contact your doctor immediately.
- Report problems: Report any issues to the FDA's Safety Reporting Portal.
⚠️ Emergency: If you experience severe symptoms after consuming this product, call 911 or Poison Control at 1-800-222-1222.
Recall Details
- Company:
- Robert Bosch Tool Corp., Mt. Prospect, Ill.
- Reason for Recall:
- The Abrasive Cut-Off Wheel packages are not properly labeled with precautionary information on proper use and operation. The failure of a user to follow the instructions below could result in injury. "! WARNING Read, understand and comply with tool manual before use. Follow OSHA and ANSI B7.1 standards. Use eye, face, dust and ear protection. Wear body apron and gloves. Speed rating of wheel must be greater than tool speed. Do not grind without guard adjusted for maximum operator protection. Mount wheel with the tool flanges provided. Run-in for one minute before application. Do not jam, twist or pinch wheel in work piece or apply excessive side pressure to the wheel. RECOIL may occur if wheel is jammed. Do not use near flammable materials or gases; fire or explosion may result. Do not expose to water, condensation or freezing. Discard wheel if dropped, cracked or chipped."
- Classification:
- Class I - Dangerous
Dangerous or defective products that predictably could cause serious health problems or death.
- Status:
- ongoing
- Hazard:
- The Abrasive Cut-Off Wheel packages are not properly labeled with precautionary information on proper use and operation. The failure of a user to follow the instructions below could result in injury. "! WARNING Read, understand and comply with tool manual before use. Follow OSHA and ANSI B7.1 standards. Use eye, face, dust and ear protection. Wear body apron and gloves. Speed rating of wheel must be greater than tool speed. Do not grind without guard adjusted for maximum operator protection. Mount wheel with the tool flanges provided. Run-in for one minute before application. Do not jam, twist or pinch wheel in work piece or apply excessive side pressure to the wheel. RECOIL may occur if wheel is jammed. Do not use near flammable materials or gases; fire or explosion may result. Do not expose to water, condensation or freezing. Discard wheel if dropped, cracked or chipped."
- Remedy:
- Consumers with abrasive cut-off wheels that are missing the safety instructions should contact Vermont American Customer Service to obtain safety warning information.
Product Images
Product Information
Full Description:
The wheels have a black, abrasive exterior; a red circular label on the interior; and are used to clean, slot, nick and cut metal. The wheels were sold under the "Vermont American" brand name had the following catalog numbers, diameters and blade thickness: Item # Diameter Blade Thickness 28026 6-1/2" 1/8" 28027 7"-7-1/4" 1/8" 28028 8" 1/8" 28030 10" 1/8" 28032 12" 1/8" 28033 14" 1/8"
Product Codes/Lot Numbers:
(About 400,000)
Official Source
Always verify recall information with the official CPSC source:
View on CPSC.govCPSC Recall Number: 06184
Related Recalls
Vermont American® 13-inch-Long Masonry Drill Bits
Robert Bosch Tool Corp., Mt. Prospect, Ill.
The drill bit packages are not properly labeled with precautionary information on proper use and operation. These and other manufacturers' 13-inch bits can bend when run at a high speed without being in contact with a work surface, resulting in loss of control of the drill and possible lacerations. The safety label should read: "! WARNING Read, understand and comply with tool manual before use. Wear eye protection. Max operating speed 600 RPM. At higher speeds the bit is likely to bend if allowed to rotate freely without contacting the work. Start drilling at low RPM and with bit tip in contact with work. To avoid bit bowing - Apply pressure only in direct line with bit and do not apply excessive pressure. Bits can bind, causing breakage or loss of control. Do not use in hammer drills or in drill press."