๐Ÿฅ

Medical Devices Recalls

Medical equipment, implants, and diagnostic devices

38,779 Total Recalls

Software anomalies were reported to affect the following system functionalities: startup and shutdown, system and network communication, motion control, image acquisition and output, dose reporting, and logs generation. Software version 3.1.7 will be installed on all 2nd edition imaging systems.

Aug 30, 2018 Diagnostic Equipment Nationwide View Details โ†’

Software anomalies were reported to affect the following system functionalities: startup and shutdown, system and network communication, motion control, image acquisition and output, dose reporting, and logs generation. Software version 3.1.7 will be installed on all 2nd edition imaging systems.

Aug 30, 2018 Diagnostic Equipment Nationwide View Details โ†’

The system's IFU contains a list of generators that the have been deemed compatible. Recent reports indicate that one energy platform is not compatible with the system. Therefore, it has been removed from the list of compatible generators within the IFU.

Aug 31, 2018 Infusion Pumps Nationwide View Details โ†’

The BACT/ALERT VIRTUO Instrument Firmware version R2.0 allows relocation of the four (4) resident calibration standards so that Field System Engineers (FSE) can service the associated cells P24 - P27, where the calibration standards typically reside. If the calibration standards are not returned to the designated locations, an anomaly may occur.

Jun 27, 2018 Diagnostic Equipment Nationwide View Details โ†’

The pouches of certain lots of product may have wrinkles along the pouch seal that could result in a channel within the seal. Should there be a channel in the pouch seal it may result in a breach in the sterility of the product.

Sep 14, 2018 Surgical Instruments Nationwide View Details โ†’

Software anomalies were reported to affect the following system functionalities: startup and shutdown, system and network communication, motion control, image acquisition and output, dose reporting, and logs generation. Software version 3.1.7 will be installed on all 2nd edition imaging systems.

Aug 30, 2018 Diagnostic Equipment Nationwide View Details โ†’

Reprocessing instructions for the SGS/SGA Surgical Handpieces have been updated with instructions of manual cleaning and specific parameters for autoclave sterilization. The previous operation manuals associated with the SGS/SGA products must be replaced by new operation manuals.

Jun 1, 2018 Implants & Prosthetics View Details โ†’

APTIO CENTRIFUGE MODULE

Siemens Healthcare Diagnostics

Class I - Dangerous

The modules may have been shipped without a warning label for potential risk of interference to pacemaker functionality.

Aug 14, 2018 Other Medical Devices Nationwide View Details โ†’

Coil overheating can occur when the device is used in Mode 2 setup. This could lead to a serious patient thermal injury. There have been no injuries reported as a result of this issue.

Dec 7, 2015 Diagnostic Equipment Nationwide View Details โ†’

Users may experience alarm fatigue due to frequent alarming relating to patient temperature deviation beyond 0.5ยฟC while in Automatic mode. 2. Users may experience a Remove from Use code 9 (RFU 9) fault condition relating to inadvertent flow alarms.3. Users may experience code RFU 27 fault condition relating to mechanical interference between the device fan and filter

Sep 6, 2018 Infusion Pumps Nationwide View Details โ†’

Atellica Solution system software (SW) version 1.13 and lower, five (5) behavioral issues were identified: 1. Reagent Lock may not work as intended with Primary Reagent ReadyPacksยฟ and Ancillary Packs when more than one (1) lot of specific Reagent kits are loaded on the analyzer at the same time. 2. Sample barcodes may be incorrectly read 3. The Atellica IM 1300 Analyzer and Atellica IM 1600 Analyzer may not run CEA dilutions at 50x and 100x. The Analyzer may post a Sample Integrity Error when 50x or 100x dilutions are ordered for Carcinoembryonic Antigen (CEA). Dilution factors lower than 50x and neat samples are not affected by this behavior. 4. The Atellica CH 930 Analyzer may continue to display the default reporting units after the reporting units have been changed. 5. The Atellica CH 930 Analyzer may not display results for sample if certain assays are configured to auto-dilute results above or below the assay measuring interval.

Jun 29, 2018 Diagnostic Equipment Nationwide View Details โ†’

These catheters may have the following deficiencies: 1) barium sulfate omission, and 2) actual catheter tip length is one centimeter shorter than printed on the tip

Aug 21, 2018 Infusion Pumps Nationwide View Details โ†’